跳至主要内容

Solids Control System Equipment Mud Cleaner


 
KOSUN high effective mud cleaner is the second or third stage solids control system equipment of drilling mud, which will deal with the drilling mud after being treated by the first stage solids control system equipment. The barite will be recovered and drilling cuttings which are bigger than barite will be removed. Then the barite in the underflow will flow into circulation tanks through the shaker screens when the weighted mud passes while the particles that are bigger than mesh will be removed.
 
KOSUN desander is used as the second stage of solids control system for drilling mud, which makes separations between 40 and 100 microns.
 
KOSUN desilter is used as the third stage of solids control system for drilling mud, which make separations between 15 and 44 microns.

1. Polyurethane (PU) Material for desander and desilter cones.
2. Desander cones can be installed between one and three 10desander cones, each cone can process 500GPM and makes a separation between 40 and 100 microns.
3. Desilter cones can be installed between eight and twenty 4or 5desilter cones ,each cone can process 80 GPM, and makes a separation between 15 and 75 microns.
4. Mechanical Deck Adjustable while operation for reliable performance.
5. Compact design with small footprint, with top feed and wire feed two option.
6. Hook-strip shaker screen for fast screens changing with PWP and PMD screens.

评论

此博客中的热门博文

Mono Screw Pump Working Principle and Apllication

M ono screw pump , also called  sewage pump  or  progressive cavity pump ,  belongs to the rotor type positive displacement pump .   M ono screw pump  is depend ing  on the screw meshing with liner on the discharge and suction cavity to conveying liquid volume change.   It is a kind of method of pressurized screw pump, a main working parts by bushing has a double helix cavity (stator) and the stator cavity and its meshing singlehead screw screw (rotor).   When the input shaft through the universal joint drive making planets revolving around the center of the stator, rotor stator, rotor, vice is continuous mesh form sealed cavity, the seal chamber volume invariably uniform axial movement, the medium from the suction end of deputy to the stator, rotor pressure side, the suction medium sealed cavity through the stator without stirring and destruction. M ono screw pump  is an ideal pump used to feed drilling fluids to ...

Drilling Waste Management Solutions

With the increasing attention to environmental protection, drilling waste randomly disposal has been seriously forbid by many countries. Considering the global need of such kind of equipment need, KOSUN  focused on drilling waste management solutions for many years. Contamination of drilling fluids  with drilled cuttings is an unavoidable consequence of successful drilling operations. If the  drilling fluid  does not carry cuttings and caving  to the surface, the rig is not either “making hole” or soon will be stuck in the hole it is making. The drill cuttings that are separated from the drilling fluid on the surface by the so lid s control equipment and some quantity of unrecoverable or economically unwanted drilling fluid are a major source of drilling waste. Drilled and formation solids that are sized smaller than can be removed by the solids control equipment are often reported as drill solids. Some quantity of drill s...

Water Based Mud Drilling Cuttings Management

In  geotechnical engineering ,   drilling fluid is used to aid the drilling of  boreholes   into the earth , o ften used while drilling  oil  and  natural gas  wells and on exploration drilling rigs , and  also for much simpler boreholes  like   water wells . Liquid drilling fluid is often called drilling mud. The three main categories of drilling fluids are water-based mud (which can be dispersed and non-dispersed), non-aqueous mud, usually called oil-based mud, and gaseous drilling fluid, in which a wide range of  gases  can be used. The main functions of drilling fluids include :  providing  hydrostatic pressure  to prevent  formation fluids  from entering into the well bore, keeping the  drill bit  cool and clean during drilling, carrying out drill cuttings, and suspending the drill cuttings while drilling is paused and when the drilling assembly is brought in and out...