跳至主要内容

Drilling Waste Management Processing Craft Description


During oil & gas exploration and production, there are lots of drilling cuttings and fluid generated. These drilling waste will leak into earth with time going which is great harm to surface and ground water and the surrounding environment even causes pollution, especially in sensitive area harmful to human health and life. Therefore, it is crucial important to drilling waste management before discharged.

Here is a simple processing procedure for drilling waste management.
  • The screw conveyor mounted under the shale shaker is used for collecting drilling cuttings from shale shakers and mud cleaners (desander or desilter), then convey the drilling cuttings to the H-G dryer for solid-liquid drilling waste management.
  • There is one conical buried tank under the shale shakers for discharging mud and alleviate the grit in mud tank. Otherwise, if serious grouting off happened, the overflow mud will enter into the conical buries tank to prevent mud grounding. There is one unit of submersible sludge pump at the end of the conical buried tank which can return the fluid to the H-G dryer for waste separation. The conical buried tank is equipped with two units of MA55 mud agitators.
  • Solids from the centrifuge is back to solid collection tank for solidification and then passed to the on-site waste temporary dumps.
  • The solids after H-G dryer and high speed VFD centrifuge get to the solidified tank by screw conveyor, and the fluid enters into the collection cabin and is pumped into high speed VFD centrifuge by screw pump for further drilling waste management.
  • The solids after high speed VFD centrifuge is transported to the on-site waste temporary dumps by screw conveyor, or discharged into the solidified tank. The solids after high speed VFD centrifuge must not enter into cuttings dryer for further processing.
  • The sediments in the conical buried tank under the H-G dryer can be dig out by special machine.
  • The system shall be facilitated with washing device for equipment cleaning.
标签：

评论

发表评论

此博客中的热门博文

Drilling Cuttings & Drilling Waste Separation Development

Drilling waste separation from the mud at the sedimentary rock shakers is also coated with such a lot mud that   square measure|they're unsuitable for the  drilling fluid recycle or disposal step or are tough to handle or transport. Constituents of the drilling cuttings or the mud coating them, like oil or metals, could leach from the drilling waste, creating them unsuitable for land application or burial needs. forms of materials will be other to drilling cuttings to solidify and stabilize them.  Solidification could be a technology that encapsulate the drilling waste  in an exceedingly monolithic solid of high structural integrity. The encapsulation is also of fine drilling waste particles or of an outsized block orinstrumentality  of drilling cuttings .  Solidification doesn't essentially invol...
发表评论
阅读全文

Drill Cuttings Disposal Management

Drill cuttings disposal is a hot topic these years with global attention to environmental protection, especially in O il & gas industry. D rill cuttings  disposal into environment without any treatment is strictly forbidden. So before disposal, a series methods must be introduced to treat the cuttings and make it reach to disposal standard. Drill cuttings are produced as the rock is broken by the drill bit advancing through the rock or soil; the cuttings are usually carried to the surface by  drilling fluid  circulating up from the drill bit   by  rotary ,  percussion , or auger methods. The drill cuttings are commonly examined to make a record (a  well log ) of the subsurface materials penetrated at various depths. In the oil industry, this is often called a  mud log .   One drilling method that does not produce drill cuttings is  core drilling , which instead produces solid cylinders of rock or soil.   In cable-tool ...
发表评论
阅读全文

Mono Screw Pump Working Principle and Apllication

M ono screw pump , also called  sewage pump  or  progressive cavity pump ,  belongs to the rotor type positive displacement pump .   M ono screw pump  is depend ing  on the screw meshing with liner on the discharge and suction cavity to conveying liquid volume change.   It is a kind of method of pressurized screw pump, a main working parts by bushing has a double helix cavity (stator) and the stator cavity and its meshing singlehead screw screw (rotor).   When the input shaft through the universal joint drive making planets revolving around the center of the stator, rotor stator, rotor, vice is continuous mesh form sealed cavity, the seal chamber volume invariably uniform axial movement, the medium from the suction end of deputy to the stator, rotor pressure side, the suction medium sealed cavity through the stator without stirring and destruction. M ono screw pump  is an ideal pump used to feed drilling fluids to ...
发表评论
阅读全文